| Moteur de recherche de fiches techniques de composants électroniques |
|
ST10F280 Fiches technique(PDF) 23 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
ST10F280 Fiches technique(HTML) 23 Page - STMicroelectronics |
|
23 / 239 page ![]() ST10F280 Ball data Doc ID 8673 Rev. 3 23/239 PORT1: P1L.0 - P1L.7, P1H.0 - P1H.7 I/O PORT1 consists of the two 8-bit bidirectional I/O ports P1L and P1H. It is bit-wise programmable for input or output via direction bits. For a pin configured as input, the output driver is put into high- impedance state. PORT1 is used as the 16-bit address bus (A) in demultiplexed bus modes and also after switching from a demultiplexed bus mode to a multiplexed bus mode. The following PORT1 pins also serve for alternate functions: C11 I/O P1L.0 B11 I/O P1L.1 D10 I/O P1L.2 C10 I/O P1L.3 B10 I/O P1L.4 A10 I/O P1L.5 D9 I/O P1L.6 C9 I/O P1L.7 C8 I/O P1H.0 D8 I/O P1H.1 A7 I/O P1H.2 B7 I/O P1H.3 C7 I P1H.4 CC24IO CAPCOM2: CC24 Capture Input D7 I P1H.5 CC25IO CAPCOM2: CC25 Capture Input C5 I P1H.6 CC26IO CAPCOM2: CC26 Capture Input C6 I P1H.7 CC27IO CAPCOM2: CC27 Capture Input XTAL1 A5 I XTAL1: Input to the oscillator amplifier and input to the internal clock generator XTAL2 A6 O XTAL2: Output of the oscillator amplifier circuit. To clock the device from an external source, drive XTAL1, while leaving XTAL2 unconnected. Minimum and maximum high/low and rise/fall times specified in the AC Characteristics must be observed. RSTIN A3 I Reset Input with Schmitt-Trigger characteristics. A low level at this pin for a specified duration while the oscillator is running resets the ST10F280. An internal pull-up resistor permits power-on reset using only a capacitor connected to VSS. In bidirectional reset mode (enabled by setting bit BDRSTEN in SYSCON register), the RSTIN line is pulled low for the duration of the internal reset sequence. RSTOUT B4 O Internal Reset Indication Output. This pin is set to a low level when the part is executing either a hardware, a software or a watchdog timer reset. RSTOUT remains low until the EINIT (end of initialization) instruction is executed. Table 1. Ball description (continued) Symbol Ball number Type Function |
|
Lien URL |
| ALLDATASHEET vous a-t-il été utile ? [ DONATE ] |
À propos de Alldatasheet | Publicité | Contactez-nous | Politique de confidentialité | Lien vers la fiche technique | Echange de liens | Fabricants All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |