ADE9000ACPZ datasheet(41/73 Pages) AD

41 / 73 page

ADE9000

Data Sheet

Rev. A | Page 40 of 72

Address

Name

Description

Reset

Access

0x030

BVAROS

Phase B total reactive power offset correction for the BVAR calculation.

0x00000000

R/W

0x031

BFWATTOS

Phase B fundamental active power offset correction for the BFWATT calculation.

0x00000000

R/W

0x032

BFVAROS

Phase B fundamental reactive power offset correction for the BFVAR calculation.

0x00000000

R/W

0x033

BIFRMSOS

Phase B current rms offset for the fundamental current rms BIFRMS calculation.

0x00000000

R/W

0x034

BVFRMSOS

Phase B voltage rms offset for the fundamental voltage rms BVFRMS calculation.

0x00000000

R/W

0x035

BVRMSONEOS

Phase B voltage rms offset for the fast rms½ BVRMSONE calculation.

0x00000000

R/W

0x036

BIRMSONEOS

Phase B current rms offset for the fast rms½ BIRMSONE calculation.

0x00000000

R/W

0x037

BVRMS1012OS

Phase B voltage rms offset for the 10 cycle rms/12 cycle rms BVRMS1012 calculation.

0x00000000

R/W

0x038

BIRMS1012OS

Phase B current rms offset for the 10 cycle rms/12 cycle rms BVRMS1012 calculation.

0x00000000

R/W

0x040

CIGAIN

Phase C current gain adjust.

0x00000000

R/W

0x041

CIGAIN0

Phase C multipoint gain correction factor. If multipoint gain and phase compensation

is enabled, with MTEN = 1 in the CONFIG0 register, an additional gain factor,

CIGAIN0 through CIGAIN5, is applied based on the CIRMS current rms amplitude

and the MTTHR_Lx and MTTHR_Hx register values.

0x00000000

R/W

0x042

CIGAIN1

Phase C multipoint gain correction factor. If multipoint gain and phase compensation

is enabled, with MTEN = 1 in the CONFIG0 register, an additional gain factor,

CIGAIN0 through CIGAIN5, is applied based on the CIRMS current rms amplitude

and the MTTHR_Lx and MTTHR_Hx register values.

0x00000000

R/W

0x043

CIGAIN2

Phase C multipoint gain correction factor. If multipoint gain and phase compensation

is enabled, with MTEN = 1 in the CONFIG0 register, an additional gain factor,

CIGAIN0 through CIGAIN5, is applied based on the CIRMS current rms amplitude

and the MTTHR_Lx and MTTHR_Hx register values.

0x00000000

R/W

0x044

CIGAIN3

Phase C Multipoint gain correction factor. If multipoint gain and phase compensation

is enabled, with MTEN = 1 in the CONFIG0 register, an additional gain factor,

CIGAIN0 through CIGAIN5, is applied based on the CIRMS current rms amplitude

and the MTTHR_Lx and MTTHR_Hx register values.

0x00000000

R/W

0x045

CIGAIN4

Phase C Multipoint gain correction factor. If multipoint gain and phase compensation

is enabled, with MTEN = 1 in the CONFIG0 register, an additional gain factor,

CIGAIN0 through CIGAIN5, is applied based on the CIRMS current rms amplitude

and the MTTHR_Lx and MTTHR_Hx register values.

0x00000000

R/W

0x046

CPHCAL0

Phase C multipoint phase correction factor. If multipoint phase and gain calibration is

disabled, with MTEN = 0 in the CONFIG0 register, the CPHCAL0 phase compensation

is applied. If multipoint phase and gain correction is enabled, with MTEN = 1, the

CPHCAL0 through CPHCAL4 value is applied, based on the CIRMS current rms

amplitude and the MTTHR_Lx and MTTHR_Hx register values.

0x00000000

R/W

0x047

CPHCAL1

Phase C multipoint phase correction factor. If multipoint phase and gain calibration is

disabled, with MTEN = 0 in the CONFIG0 register, the CPHCAL0 phase compensation

is applied. If multipoint phase and gain correction is enabled, with MTEN = 1, the

CPHCAL0 through CPHCAL4 value is applied, based on the CIRMS current rms

amplitude and the MTTHR_Lx and MTTHR_Hx register values.

0x00000000

R/W

0x048

CPHCAL2

Phase C multipoint phase correction factor. If multipoint phase and gain calibration is

disabled, with MTEN = 0 in the CONFIG0 register, the CPHCAL0 phase compensation

is applied. If multipoint phase and gain correction is enabled, with MTEN = 1, the

CPHCAL0 through CPHCAL4 value is applied, based on the CIRMS current rms

amplitude and the MTTHR_Lx and MTTHR_Hx register values.

0x00000000

R/W

0x049

CPHCAL3

Phase C multipoint phase correction factor. If multipoint phase and gain calibration is

disabled, with MTEN = 0 in the CONFIG0 register, the CPHCAL0 phase compensation

is applied. If multipoint phase and gain correction is enabled, with MTEN = 1, the

CPHCAL0 through CPHCAL4 value is applied, based on the CIRMS current rms

amplitude and the MTTHR_Lx and MTTHR_Hx register values.

0x00000000

R/W

0x04A

CPHCAL4

Phase C multipoint phase correction factor. If multipoint phase and gain calibration is

disabled, with MTEN = 0 in the CONFIG0 register, the CPHCAL0 phase compensation

is applied. If multipoint phase and gain correction is enabled, with MTEN = 1, the

CPHCAL0 through CPHCAL4 value is applied, based on the CIRMS current rms

amplitude and the MTTHR_Lx and MTTHR_Hx register values.

0x00000000

R/W

0x04B

CVGAIN

Phase C voltage gain adjust.

0x00000000

R/W

0x04C

CIRMSOS

Phase C current rms offset for the CIRMS calculation.

0x00000000

R/W

0x04D

CVRMSOS

Phase C voltage rms offset for the CVRMS calculation.

0x00000000

R/W

ADE9000ACPZ Fiches technique(PDF) 41 Page - Analog Devices

ADE9000ACPZ Fiches technique(HTML) 41 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73

Fiches technique Télécharger

Lien URL