ADE9000ACPZ datasheet(40/73 Pages) AD

40 / 73 page

Data Sheet

ADE9000

Rev. A | Page 39 of 72

Address

Name

Description

Reset

Access

0x013

AIFRMSOS

Phase A current rms offset for the fundamental current rms, AIFRMS calculation.

0x00000000

R/W

0x014

AVFRMSOS

Phase A voltage rms offset for the fundamental voltage rms, AVFRMS calculation.

0x00000000

R/W

0x015

AVRMSONEOS

Phase A voltage rms offset for the fast rms½ AVRMSONE calculation.

0x00000000

R/W

0x016

AIRMSONEOS

Phase A current rms offset for the fast rms½ AIRMSONE calculation.

0x00000000

R/W

0x017

AVRMS1012OS

Phase A voltage rms offset for the 10 cycle rms/12 cycle rms AVRMS1012 calculation.

0x00000000

R/W

0x018

AIRMS1012OS

Phase A current rms offset for the 10 cycle rms/12 cycle rms AIRMS1012 calculation.

0x00000000

R/W

0x020

BIGAIN

Phase B current gain adjust.

0x00000000

R/W

0x021

BIGAIN0

Phase B multipoint gain correction factor. If multipoint gain and phase compensation

is enabled, with MTEN = 1 in the CONFIG0 register, an additional gain factor,

BIGAIN0 through BIGAIN5, is applied based on the BIRMS current rms amplitude

and the MTTHR_Lx and MTTHR_Hx register values.

0x00000000

R/W

0x022

BIGAIN1

Phase B multipoint gain correction factor. If multipoint gain and phase compensation

is enabled, with MTEN = 1 in the CONFIG0 register, an additional gain factor,

BIGAIN0 through BIGAIN5, is applied based on the BIRMS current rms amplitude

and the MTTHR_Lx and MTTHR_Hx register values.

0x00000000

R/W

0x023

BIGAIN2

Phase B multipoint gain correction factor. If multipoint gain and phase compensation

is enabled, with MTEN = 1 in the CONFIG0 register, an additional gain factor,

BIGAIN0 through BIGAIN5, is applied based on the BIRMS current rms amplitude

and the MTTHR_Lx and MTTHR_Hx register values.

0x00000000

R/W

0x024

BIGAIN3

Phase B multipoint gain correction factor. If multipoint gain and phase compensation

is enabled, with MTEN = 1 in the CONFIG0 register, an additional gain factor,

BIGAIN0 through BIGAIN5, is applied based on the BIRMS current rms amplitude

and the MTTHR_Lx and MTTHR_Hx register values.

0x00000000

R/W

0x025

BIGAIN4

Phase B multipoint gain correction factor. If multipoint gain and phase compensation

is enabled, with MTEN = 1 in the CONFIG0 register, an additional gain factor,

BIGAIN0 through BIGAIN5, is applied based on the BIRMS current rms amplitude

and the MTTHR_Lx and MTTHR_Hx register values.

0x00000000

R/W

0x026

BPHCAL0

Phase B multipoint phase correction factor. If multipoint phase and gain calibration is

disabled, with MTEN = 0 in the CONFIG0 register, the BPHCAL0 phase compensation

is applied. If multipoint phase and gain correction is enabled, with MTEN = 1, the

BPHCAL0 through BPHCAL4 value is applied based on the BIRMS current rms

amplitude and the MTTHR_Lx and MTTHR_Hx register values.

0x00000000

R/W

0x027

BPHCAL1

Phase B multipoint phase correction factor. If multipoint phase and gain calibration is

disabled, with MTEN = 0 in the CONFIG0 register, the BPHCAL0 phase compensation

is applied. If multipoint phase and gain correction is enabled, with MTEN = 1, the

BPHCAL0 through BPHCAL4 value is applied based on the BIRMS current rms

amplitude and the MTTHR_Lx and MTTHR_Hx register values.

0x00000000

R/W

0x028

BPHCAL2

Phase B multipoint phase correction factor. If multipoint phase and gain calibration is

disabled, with MTEN = 0 in the CONFIG0 register, the BPHCAL0 phase compensation

is applied. If multipoint phase and gain correction is enabled, with MTEN = 1, the

BPHCAL0 through BPHCAL4 value is applied based on the BIRMS current rms

amplitude and the MTTHR_Lx and MTTHR_Hx register values.

0x00000000

R/W

0x029

BPHCAL3

Phase B multipoint phase correction factor. If multipoint phase and gain calibration is

disabled, with MTEN = 0 in the CONFIG0 register, the BPHCAL0 phase compensation

is applied. If multipoint phase and gain correction is enabled, with MTEN = 1, the

BPHCAL0 through BPHCAL4 value is applied based on the BIRMS current rms

amplitude and the MTTHR_Lx and MTTHR_Hx register values.

0x00000000

R/W

0x02A

BPHCAL4

Phase B multipoint phase correction factor. If multipoint phase and gain calibration is

disabled, with MTEN = 0 in the CONFIG0 register, the BPHCAL0 phase compensation

is applied. If multipoint phase and gain correction is enabled, with MTEN = 1, the

BPHCAL0 through BPHCAL4 value is applied based on the BIRMS current rms

amplitude and the MTTHR_Lx and MTTHR_Hx register values.

0x00000000

R/W

0x02B

BVGAIN

Phase B voltage gain adjust.

0x00000000

R/W

0x02C

BIRMSOS

Phase B current rms offset for the BIRMS calculation.

0x00000000

R/W

0x02D

BVRMSOS

Phase B voltage rms offset for the BVRMS calculation.

0x00000000

R/W

0x02E

BPGAIN

Phase B power gain adjust for the BWATT, BVA, BVAR, BFWATT, BFVA, and BFVAR

calculations.

0x00000000

R/W

0x02F

BWATTOS

Phase B total active power offset correction for the BWATT calculation.

0x00000000

R/W

ADE9000ACPZ Fiches technique(PDF) 40 Page - Analog Devices

ADE9000ACPZ Fiches technique(HTML) 40 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73

Fiches technique Télécharger

Lien URL