| Moteur de recherche de fiches techniques de composants électroniques |
|
SPEAR320S-2 Fiches technique(PDF) 47 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
SPEAR320S-2 Fiches technique(HTML) 47 Page - STMicroelectronics |
|
47 / 113 page ![]() Note: 1 Table 15 cells filled with ‘0’ or ‘1’ are unused and unless otherwise configured as Alternate function or GPIO, the corresponding pin is held at low or high level respectively by the internal logic. 2Pins shared by EMI and FSMC: Depending on the AHB address to be accessed the pins are used for EMI or FSMC transfers. 3Reset state definition: the state of each pin during reset and after reset release. Device is in configuration mode 1 (default state) : OH= Output high level, OL output low level, IPU = input pull up, IPD = input pull down. 4 Full debug mode: refer to Table 32: Ball sharing during debug for details on debug mode selection. 5 Functional mode definition: in functional mode the I/O works as configured by the application (depending on settings for Configuration mode 1- 4/Extended mode/Alternate function). 6 Refer to Table 16: Table shading reference for Table 15 multiplexing scheme for colors and shading used in Table 15 cells to identify pin groups PL_GPIO_5/D2 UART1_RI I2C0_SDA Functional mode IPU GPIO_5 0 UART5_TX 0 0 PL_GPIO_4/C1 UART1_DCD I2C0_SCL IPU GPIO_4 0 UART5_RX 0 0 PL_GPIO_3/D1 UART1_DSR UART0_RX IPD GPIO_3 I2C2_SDA UART6_TX 0 0 PL_GPIO_2/E4 UART1_RTS UART0_TX OH GPIO_2 I2C2_SCL UART6_RX 0 0 PL_GPIO_1/E3 I2C2_SDA IrDA_RX IPU GPIO_1 UART2_TX UART2_TX UART2_TX UART2_TX PL_GPIO_0/F3 I2C2_SCL IrDA_TX OL GPIO_0 UART2_RX UART2_RX UART2_RX UART2_RX PL_CLK1/K17 UART3_TX PL_CLK1 OL GPIO_98 CLCP 0 I2C1_SDA SD_LED PL_CLK2/J17 UART3_RX PL_CLK2 OL GPIO_99 SD_CLK SD_CLK I2C1_SCL SD_CLK PL_CLK3/J16 UART4_TX PL_CLK3 IPU GPIO_100 SD_WP SD_WP 0 SD_WP PL_CLK4/H17 UART4_RX PL_CLK4 IPU GPIO_101 SD_CMD SD_CMD 0 SD_CMD Table 15. PL_GPIO/PL_CLK multiplexing scheme and reset states (continued) PL_GPIO_# / ball number Extended mode primary function (SW defined) Alternate function (SW defined) Full debug mode Legacy configuration mode (SW defined) Mode 1 (Default configuration after reset) Mode 2 Mode 3 Mode 4 |
|
Lien URL |
| ALLDATASHEET vous a-t-il été utile ? [ DONATE ] |
À propos de Alldatasheet | Publicité | Contactez-nous | Politique de confidentialité | Lien vers la fiche technique | Echange de liens | Fabricants All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |