CS89712 datasheet(64/170 Pages) CIRRUS

64 / 170 page

CS89712

DS502PP2

(Destination Address, Source Address, Length

field and LLC data). If the frame is less than 64

bytes, including CRC, the CS89712 adds pad bits if

configured to do so. Finally, the CS89712 appends

the proper 32-bit CRC value.

2.34.2

Transmit Configuration

After each reset, the Ethernet port must be config-

ured for transmit operation. This can be done auto-

matically using an attached EEPROM, or by

writing configuration commands to the Ethernet

port’s internal registers (see Section 2.6, “Ethernet

EEPROM Configurations”). The items that must

be configured include which physical interface to

use and which transmit events cause interrupts.

2.34.2.1

Configuring the Physical Interface

Configuring the Physical Interface is accomplished

via the LineCTL register. Bit 6 enables reception

and bit 9 enables transmission, while bits B and D

control backoff and deferral. See Section 3.18.12

on page 127 for LineCTL details.

Note that the CS89712 transmits in 10BASE-T

mode when no link pulses are being received only

if bit DisableLT is set in the Test Control register.

2.34.2.2

Selecting Interrupt Events

The TxCFG and BufCFG registers are used to de-

termine which transmit events will cause inter-

rupts. TxCFG [B:8] and F, and BufCFG [9:8] and

are

used.

Refer

Section 3.18.5

and

Section 3.18.8 for details.

2.34.3

Changing the Configuration

When software configures these registers it does

not need to change them for subsequent packet

transmissions. The TxCFG or BufCFG register bits

may be changed at any time. The effects of the

change are noticed immediately. Any changes in

the Interrupt Enable (iE) bits may affect the packet

currently being transmitted.

If the LineCTL register bits are changed after ini-

tialization, the ModBackoffE bit and any receive

related bit (LoRxSquelch, SerRxON) may be

changed at any time.

2.34.4

Enabling CRC Generation/Padding

Whenever the software issues a Transmit Request

command, it must indicate whether or not the Cy-

clic Redundancy Check (CRC) value should be ap-

pended to the transmit frame, and whether or not

pad bits should be added (if needed). Bits C and D

of TxCMD are used, refer to Table 3.18.7 on

page 122.

2.34.5

Individual Packet Transmission

Whenever the software has a packet to transmit, it

must issue a Transmit Request to the Ethernet port

consisting of the following three operations in the

exact order shown:

1) The software must write a Transmit Command

to the TxCMD register. The contents of the Tx-

CMD register may be read back from the TxC-

MD register.

2) The software must write the frame’s length to

the TxLength register.

3) Software must read the BusST register.

The information written to the TxCMD register

tells the Ethernet port how to transmit the next

frame. Appropriate bits in TxCMD are 6:9, C and

D. Refer to Table 3.19 on page 133.

For each individual packet transmission, software

must issue a complete Transmit Request. Further-

more, the software must write to the TxCMD reg-

ister before each packet transmission, even if the

contents of the TxCMD register do not change.

2.34.6

Transmit in Poll Mode

In poll mode, Rdy4TxiE bit (BufCFG register bit 8)

must be clear (Interrupt Disabled). The transmit op-

eration occurs in the following order:

CS89712 Fiches technique(PDF) 64 Page - Cirrus Logic

CS89712 Fiches technique(HTML) 64 Page - Cirrus Logic

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Fiches technique Télécharger

Lien URL