JS28F256P30T85 datasheet(52/102 Pages) INTEL

52 / 102 page

1-Gbit P30 Family

April 2005

Intel StrataFlash® Embedded Memory (P30)

Datasheet

Order Number: 306666, Revision: 001

Write

0x10

Alternate Word

Program Setup

Equivalent to the Word Program Setup command, 0x40.

0xE8

Buffered Program

This command loads a variable number of words up to the buffer size of 32

words onto the program buffer.

0xD0

Buffered Program

Confirm

The confirm command is Issued after the data streaming for writing into the

buffer is done. This instructs the WSM to perform the Buffered Program

algorithm, writing the data from the buffer to the flash memory array.

0x80

BEFP Setup

First cycle of a 2-cycle command; initiates Buffered Enhanced Factory

Program mode (BEFP). The CUI then waits for the BEFP Confirm command,

0xD0, that initiates the BEFP algorithm. All other commands are ignored when

BEFP mode begins.

0xD0

BEFP Confirm

If the previous command was BEFP Setup (0x80), the CUI latches the address

and data, and prepares the device for BEFP mode.

Erase

0x20

Block Erase Setup

First cycle of a 2-cycle command; prepares the CUI for a block-erase

operation. The WSM performs the erase algorithm on the block addressed by

the Erase Confirm command. If the next command is not the Erase Confirm

(0xD0) command, the CUI sets Status Register bits SR[4] and SR[5], and

places the device in read status register mode.

0xD0

Block Erase Confirm

If the first command was Block Erase Setup (0x20), the CUI latches the

address and data, and the WSM erases the addressed block. During block-

erase operations, the device responds only to Read Status Register and Erase

Suspend commands. CE# or OE# must be toggled to update the Status

Status Register Data for synchronous Non-array reads

Suspend

0xB0

Program or Erase

Suspend

This command issued to any device address initiates a suspend of the

currently-executing program or block erase operation. The Status Register

indicates successful suspend operation by setting either SR[2] (program

suspended) or SR[6] (erase suspended), along with SR[7] (ready). The Write

State Machine remains in the suspend mode regardless of control signal states

(except for RST# asserted).

0xD0

Suspend Resume

This command issued to any device address resumes the suspended program

or block-erase operation.

Block Locking/

Unlocking

0x60

Lock Block Setup

First cycle of a 2-cycle command; prepares the CUI for block lock configuration

changes. If the next command is not Block Lock (0x01), Block Unlock (0xD0),

or Block Lock-Down (0x2F), the CUI sets Status Register bits SR[4] and SR[5],

indicating a command sequence error.

0x01

Lock Block

If the previous command was Block Lock Setup (0x60), the addressed block is

locked.

0xD0

Unlock Block

If the previous command was Block Lock Setup (0x60), the addressed block is

unlocked. If the addressed block is in a lock-down state, the operation has no

effect.

0x2F

Lock-Down Block

If the previous command was Block Lock Setup (0x60), the addressed block is

locked down.

Protection

0xC0

Program Protection

First cycle of a 2-cycle command; prepares the device for a Protection Register

or Lock Register program operation. The second cycle latches the register

address and data, and starts the programming algorithm

Configuration

0x60

Read Configuration

First cycle of a 2-cycle command; prepares the CUI for device read

configuration. If the Set Read Configuration Register command (0x03) is not

the next command, the CUI sets Status Register bits SR[4] and SR[5],

indicating a command sequence error.

0x03

Read Configuration

If the previous command was Read Configuration Register Setup (0x60), the

CUI latches the address and writes A[15:0] to the Read Configuration Register.

Following a Configure Read Configuration Register command, subsequent

read operations access array data.

Table 21.

Command Codes and Definitions (Sheet 2 of 2)

Mode

Code

Device Mode

Description

JS28F256P30T85 Fiches technique(PDF) 52 Page - Intel Corporation

JS28F256P30T85 Fiches technique(HTML) 52 Page - Intel Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Fiches technique Télécharger

Lien URL