JS28F256P30T85 datasheet(48/102 Pages) INTEL

48 / 102 page

1-Gbit P30 Family

April 2005

Intel StrataFlash® Embedded Memory (P30)

Datasheet

Order Number: 306666, Revision: 001

9.0

Device Operations

This section provides an overview of device operations. The system CPU provides control of all in-

system read, write, and erase operations of the device via the system bus. The on-chip Write State

Machine (WSM) manages all block-erase and word-program algorithms.

Device commands are written to the Command User Interface (CUI) to control all flash memory

device operations. The CUI does not occupy an addressable memory location; it is the mechanism

through which the flash device is controlled.

9.1

Bus Operations

CE# low and RST# high enable device read operations. The device internally decodes upper

address inputs to determine the accessed block. ADV# low opens the internal address latches. OE#

low activates the outputs and gates selected data onto the I/O bus.

In asynchronous mode, the address is latched when ADV# goes high or continuously flows through

if ADV# is held low. In synchronous mode, the address is latched by the first of either the rising

ADV# edge or the next valid CLK edge with ADV# low (WE# and RST# must be VIH; CE# must

be VIL).

Bus cycles to/from the P30 device conform to standard microprocessor bus operations. Table 19

summarizes the bus operations and the logic levels that must be applied to the device control signal

inputs.

9.1.1

Reads

To perform a read operation, RST# and WE# must be deasserted while CE# and OE# are asserted.

CE# is the device-select control. When asserted, it enables the flash memory device. OE# is the

data-output control. When asserted, the addressed flash memory data is driven onto the I/O bus.

See Section 10.0, “Read Operations” on page 53 for details on the available read modes, and see

Section 14.0, “Special Read States” on page 75 for details regarding the available read states.

Table 19.

Bus Operations Summary

Bus Operation

RST#

CLK

ADV#

CE#

OE#

WE#

WAIT

DQ[15:0]

Notes

Read

Asynchronous

VIH

Deasserted

Output

Synchronous

VIH

Running

Driven

Output

Write

VIH

High-Z

Input

Output Disable

VIH

High-Z

Standby

VIH

High-Z

Reset

VIL

High-Z

2,3

Notes:

Refer to the Table 20, “Command Bus Cycles” on page 50 for valid DQ[15:0] during a write operation.

X = Don’t Care (H or L).

RST# must be at VSS ± 0.2 V to meet the maximum specified power-down current.

JS28F256P30T85 Fiches technique(PDF) 48 Page - Intel Corporation

JS28F256P30T85 Fiches technique(HTML) 48 Page - Intel Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Fiches technique Télécharger

Lien URL