DP83847 datasheet(13/60 Pages) NSC

13 / 60 page

www.national.com

given PHYAD input is resistively pulled high, then the cor-

responding output will be configured as an active low

driver. Refer to Figure 1 for an example of a PHYAD con-

nection to external components. In this example, the

PHYAD strapping results in address 00011 (03h).

The adaptive nature of the LED outputs helps to simplify

potential implementation issues of these dual purpose pins.

2.3 LED INTERFACES

The DP83847 has 6 Light Emitting Diode (LED) outputs,

each capable to drive a maximum of 10 mA, to indicate the

status of Link, Transmit, Receive, Collision, Speed, and

Full/Half Duplex operation. The LED_CFG strap option is

used to configure the LED_FDPLX output for use as an

LED driver or more general purpose control pin. See the

table below:

The LED_FDPLX pin indicates the Half or Full Duplex con-

figuration of the port in both 10 Mb/s and 100 Mb/s opera-

tion. Since this pin is also used as the PHY address strap

option, the polarity of this indicator may be adjusted so that

in the “active” (FULL DUPLEX selected) state it drives

against the pullup/pulldown strap. In this configuration it is

suitable for use as an LED. When LED_CFG is high this

mode is selected and DsPHYTER automatically adjusts the

polarity of the output. If LED_CFG is low, the output drives

high to indicate the “active” state. In this configuration the

output

suitable for use

a control pin.

The

LED_SPEED pin indicates 10 or 100 Mb/s data rate of the

port. The standard CMOS driver goes high when operating

in 100 Mb/s operation. Since this pin is not utilized as a

strap option, it is not affected by polarity adjustment.

The LED_GDLNK pin indicates the link status of the port.

Since this pin is also used as the PHY address strap

option, the polarity of this indicator is adjusted to be the

inverse of the strap value.

In 100BASE-T mode, link is established as a result of input

receive amplitude compliant with TP-PMD specifications

which will result in internal generation of signal detect.

10 Mb/s Link is established as a result of the reception of at

least seven consecutive normal Link Pulses or the recep-

tion of a valid 10BASE-T packet. This will cause the asser-

tion of GD_LINK. GD_LINK will deassert in accordance

with the Link Loss Timer as specified in IEEE 802.3.

The Collision LED indicates the presence of collision activ-

ity for 10 Mb/s or 100 Mb/s Half Duplex operation. This bit

has no meaning in Full Duplex operation and will be deas-

serted when the port is operating in Full Duplex. Since this

pin is also used as the PHY address strap option, the

polarity of this indicator is adjusted to be the inverse of the

strap value. In 10 Mb/s half duplex mode, the collision LED

is based on the COL signal. When in this mode, the user

should disable the Heartbeat (SQE) to avoid asserting the

COL LED during transmission. See Section 3.4.2 for more

information about the Heartbeat signal.

The LED_RX and LED_TX pins indicate the presence of

transmit and/or receive activity. Since these pins are also

used in PHY address strap options, the polarity is adjusted

to be the inverse of the respective strap values.

2.4 Half Duplex vs. Full Duplex

The DP83847 supports both half and full duplex operation

at both 10 Mb/s and 100 Mb/s speeds.

Half-duplex is the standard, traditional mode of operation

which relies on the CSMA/CD protocol to handle collisions

and network access. In Half-Duplex mode, CRS responds

to both transmit and receive activity in order to maintain

compliance with IEEE 802.3 specification.

Since the DP83847 is designed to support simultaneous

transmit and receive activity it is capable of supporting full-

Figure 1. PHYAD Strapping and LED Loading Example

VCC

PHYAD0 = 1

PHYAD1 = 1

PHYAD2 = 0

PHYAD3 = 0

PHYAD4= 0

Table 3. LED Mode Select

LED_CFG

Mode Description

LED polarity adjusted

Duplex active-high

DP83847 Fiches technique(PDF) 13 Page - National Semiconductor (TI)

DP83847 Fiches technique(HTML) 13 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Fiches technique Télécharger

Lien URL