LAN8740 datasheet(21/136 Pages) MICROCHIP

21 / 136 page

 2013-2015 Microchip Technology Inc.

DS00001987A-page 21

LAN8740A/LAN8740Ai

3.1.2.7

Receive Data Valid Signal

The Receive Data Valid signal (RXDV) indicates that recovered and decoded nibbles are being presented on the

RXD[3:0] outputs synchronous to RXCLK. RXDV becomes active after the /J/K/ delimiter has been recognized and RXD

is aligned to nibble boundaries. It remains active until either the /T/R/ delimiter is recognized or link test indicates failure

or SIGDET becomes false.

RXDV is asserted when the first nibble of translated /J/K/ is ready for transfer over the Media Independent Interface (MII

mode).

3.1.2.8

Receiver Errors

During a frame, unexpected code-groups are considered receive errors. Expected code groups are the DATA set (0

through F), and the /T/R/ (ESD) symbol pair. When a receive error occurs, the RXER signal is asserted and arbitrary

data is driven onto the RXD[3:0] lines. Should an error be detected during the time that the /J/K/ delimiter is being

decoded (bad SSD error), RXER is asserted true and the value ‘1110’ is driven onto the RXD[3:0] lines. Note that the

Valid Data signal is not yet asserted when the bad SSD error occurs.

3.1.2.9

100M Receive Data Across the MII/RMII Interface

In MII mode, the 4-bit data nibbles are sent to the MII block. These data nibbles are clocked to the controller at a rate

of 25 MHz. The controller samples the data on the rising edge of RXCLK. To ensure that the setup and hold require-

ments are met, the nibbles are clocked out of the transceiver on the falling edge of RXCLK. RXCLK is the 25 MHz output

clock for the MII bus. It is recovered from the received data to clock the RXD bus. If there is no received signal, it is

derived from the system reference clock (XTAL1/CLKIN).

When tracking the received data, RXCLK has a maximum jitter of 0.8 ns (provided that the jitter of the input clock,

XTAL1/CLKIN, is below 100 ps).

In RMII mode, the 2-bit data nibbles are sent to the RMII block. These data nibbles are clocked to the controller at a rate

of 50 MHz. The controller samples the data on the rising edge of XTAL1/CLKIN (REF_CLK). To ensure that the setup

and hold requirements are met, the nibbles are clocked out of the transceiver on the falling edge of XTAL1/CLKIN

(REF_CLK).

3.1.3

10BASE-T TRANSMIT

Data to be transmitted comes from the MAC layer controller. The 10BASE-T transmitter receives 4-bit nibbles from the

MII at a rate of 2.5 MHz and converts them to a 10 Mbps serial data stream. The data stream is then Manchester-

encoded and sent to the analog transmitter, which drives a signal onto the twisted pair via the external magnetics.

The 10M transmitter uses the following blocks:

• MII (digital)

• TX 10M (digital)

• 10M Transmitter (analog)

• 10M PLL (analog)

FIGURE 3-3:

RELATIONSHIP BETWEEN RECEIVED DATA AND SPECIFIC MII SIGNALS

data data data data

RXD

RX_DV

RX_CLK

data data data data

CLEAR-TEXT

Idle

LAN8740 Fiches technique(PDF) 21 Page - Microchip Technology

LAN8740 Fiches technique(HTML) 21 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Fiches technique Télécharger

Lien URL