| Moteur de recherche de fiches techniques de composants électroniques |
|
CS5460 Fiches technique(PDF) 21 Page - Cirrus Logic |
|
|
|||||||||||||||||||||||||||||
CS5460 Fiches technique(HTML) 21 Page - Cirrus Logic |
|
21 / 34 page ![]() CS5460 DS279PP5 21 4. REGISTER DESCRIPTION Notes: * “RA[4:0]” => register address bits in the Register Read/Write Command word ** “default” => bit status after reset 4.1 Configuration Register Address: RA[4:0]* = 0x00 Default** = 0x000001 K[3:0] Clock divider. A 4 bit binary number ranging from 0 to 15 used to divide the value of MCLK to generate the internal clock DCLK. The internal clock frequency of DCLK = MCLK/K. Valid val- ues are 1,2, and 4. 0001 = divide by 1 (default) 0010 = divide by 2 0100 = divide by 4 iCPU Inverts the CPUCLK clock. In order to reduce the level of noise present when analog signals are sampled, the logic driven by CPUCLK should not be active during the sample edge. 0 = normal operation (default) 1 = minimize noise when CPUCLK is driving rising edge logic IHPF Control the use of the High Pass Filter on the Current Channel. 0 = High-pass filter is disabled. If VHPF is set, use all-pass filter. Otherwise, no filter is used. (default) 1 = High-pass filter is enabled. VHPF Control the use of the High Pass Filter on the voltage Channel. 0 = High-pass filter is disabled. If IHPF is set, use all-pass filter. Otherwise, no filter is used. (default) 1 = High-pass filter enabled RS Start a chip reset cycle when set 1. The reset cycle lasts for less than 10 XIN cycles. The bit is automatically returned to 0 by the reset cycle. DL0 When EOD = 1, EDIR becomes a user defined pin. DL0 sets the value of the EDIR pin. Default = '0' DL1 When EOD = 1, EOUT becomes a user defined pin. DL1 sets the value of the EOUT pin. Default = '0' EOD Allows the EOUT and EDIR pins to be controlled by the DL0 and DL1 bits. EOUT and EDIR can also be accessed using the status register. 0 = Normal operation of the EOUT and EDIR pins. (default) 1 = DL0 and DL1 bits control the EOUT and EDIR pins. SI[1:0] Soft interrupt configuration. Select the desired pin behavior for indication of an interrupt. 00 = active low level (default) 23 22 21 20 19 18 17 16 PC3 PC2 PC1 PC0 0 0 0 Gi 15 14 13 12 11 10 9 8 EWA PH1 PH0 SI1 SI0 EOD DL1 DL0 765 4321 0 RS VHPF IHPF iCPU K3 K2 K1 K0 |
|
Lien URL |
| ALLDATASHEET vous a-t-il été utile ? [ DONATE ] |
À propos de Alldatasheet | Publicité | Contactez-nous | Politique de confidentialité | Lien vers la fiche technique | Echange de liens | Fabricants All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |