ST7263BDX datasheet(75/145 Pages) STMICROELECTRONICS

75 / 145 page

ST7263BDx ST7263BHx ST7263BKx ST7263BE

75/145

Serial communication interface (Cont’d)

Control Register 2 (SCICR2)

Read/Write

Reset value: 0000 0000 (00h)

Bit 7 = TIE Transmitter interrupt enable.

This bit is set and cleared by software.

0: Interrupt is inhibited

1: An SCI interrupt is generated whenever

TDRE=1 in the SCISR register

Bit 6 = TCIE Transmission complete interrupt ena-

ble

This bit is set and cleared by software.

0: Interrupt is inhibited

1: An SCI interrupt is generated whenever TC=1 in

the SCISR register

Bit 5 = RIE Receiver interrupt enable.

This bit is set and cleared by software.

0: Interrupt is inhibited

1: An SCI interrupt is generated whenever OR=1

or RDRF=1 in the SCISR register

Bit 4 = ILIE Idle line interrupt enable.

This bit is set and cleared by software.

0: Interrupt is inhibited

1: An SCI interrupt is generated whenever IDLE=1

in the SCISR register.

Bit 3 = TE Transmitter enable.

This bit enables the transmitter. It is set and

cleared by software.

0: Transmitter is disabled

1: Transmitter is enabled

Notes:

– During transmission, a “0” pulse on the TE bit

(“0” followed by “1”) sends a preamble (idle line)

after the current word.

– When TE is set there is a 1 bit-time delay before

the transmission starts.

Caution: The TDO pin is free for general purpose

I/O only when the TE and RE bits are both cleared

(or if TE is never set).

Bit 2 = RE Receiver enable.

This bit enables the receiver. It is set and cleared

by software.

0: Receiver is disabled

1: Receiver is enabled and begins searching for a

start bit

Bit 1 = RWU Receiver wake-up.

This bit determines if the SCI is in mute mode or

not. It is set and cleared by software and can be

cleared by hardware when a wake-up sequence is

recognized.

0: Receiver in Active mode

1: Receiver in Mute mode

Note: Before selecting Mute mode (setting the

RWU bit), the SCI must receive some data first,

otherwise it cannot function in Mute mode with

wakeup by idle line detection.

Bit 0 = SBK Send break.

This bit set is used to send break characters. It is

set and cleared by software.

0: No break character is transmitted

1: Break characters are transmitted

Note: If the SBK bit is set to “1” and then to “0”, the

transmitter will send a BREAK word at the end of

the current word.

TIE

TCIE

RIE

ILIE

RWU

SBK

ST7263BDX Fiches technique(PDF) 75 Page - STMicroelectronics

ST7263BDX Fiches technique(HTML) 75 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Fiches technique Télécharger

Lien URL