TLA5000 datasheet(3/4 Pages) ETC

3 / 4 page

TLA5000 Series Logic Analyzers

TLA5201 • TLA5202 • TLA5203 • TLA5204

Logic Analyzers • www.tektronix.com/logic_analyzers

iView

™ (Integrated View)

Capability

TDS oscilloscope configuration requirements –

The iView cable does not connect fully to the

TDS1000/2000 Series oscilloscopes without a GPIB

extender. Tektronix recommends a standard GPIB

cable as an extender, or order a cable extender

(National Instruments part number 181638-1).

TDS2CMAX Communications Extension Module

required for iView capability on any TDS1000/2000

Series. TDS3GM GPIB/RS-232 Interface Module

required for iView capability on any TDS3000 Series.

TDS3GV GPIB/RS-232/VGA Interface Module

required for iView capability on any TDS3000B

Series.

Number of TDS oscilloscopes that can be

connected to a TLA system – 1.

External Oscilloscopes Supported –

TDS1000 Series.

TDS2000 Series.

TDS3000/3000B Series.

TDS5000/5000B Series.

TDS6000/6000B Series.

TDS7000/7000B Series.

CSA7000/7000B Series.

TDS684C, TDS694C.

TDS754C, TDS784C, TDS724D, TDS754D,

TDS784D, TDS794D.

TLA Connections – USB, Trigger In, Trigger Out,

Clock Out.

TDS Connections – GPIB, Trigger In, Trigger Out,

Clock In (when available).

Setup – iView external oscilloscope wizard

automates setup.

Data Correlation – After TDS oscilloscope acquisition

is complete, data is automatically transferred to the

TLA and time correlated with the TLA acquisition data.

Deskew – TDS and TLA data is automatically

deskewed and time correlated when using the iView

external oscilloscope cable.

iView External Oscilloscope Cable Length – 2 m.

PC Characteristics

Operating System – Microsoft Windows 2000

Professional SP4.

Processor – Intel Celeron 2.0 GHz.

Chipset – Intel 845 GV.

DRAM – 512 MB SDRAM.

Sound – 16-Bit I/O and Mic In port.

Hard Disk Drive – 80 GB.

CD-ROM – Internal 24/10/24 CD-RW.

Floppy Disk Drive – Built-in 3.5 inch, 1.44 MB drive.

Integral Controls

Front-Panel Display –

Size: 10.4-inch diagonal.

Type: Active-matrix color TFT LCD with backlight.

Resolution: 1024x768.

Colors: 256 K.

Simultaneous Display Capability – The front-

panel and secondary displays can be operated

simultaneously using the same resolution. The

secondary external display can be used simultane-

ously using an independent resolution.

Front-panel Controls – Special function knobs for

instrument control and mini-QWERTY keypad.

External Peripheral Interfaces

External Display Port Type – Female DB15 SVGA

connector.

External Display Resolution – Up to 1600x1200

non-interlaced at 16.8 M colors.

LAN Port Type – 10/100Base-T, RJ-45.

External Keyboard Port Type – PS2 mini-DIN.

External Mouse Port Type – PS2 mini-DIN.

Parallel Interface Port Type – Female DB25.

Parallel Interface Modes – Centronics mode,

EPP (Extended Parallel Port), ECP (Microsoft

high-speed mode).

Serial Interface Port Type – Male DB9.

Audio Out Port Type – Stereo minijack.

Mic In Port Type – Minijack.

USB Port – Two USB 2.0.

Symbolic Support

Number of Symbols/Ranges – Unlimited (limited

only by amount of virtual memory available on TLA).

Object File Formats Supported –

IEEE695

OMF 51, OMF 86, OMF 166, OMF 286,

OMF 386

COFF

Elf/Dwarf 1 and 2

Elf/Stabs

TSF (TSF is a generic ASCII file format

documented in the TLA user manual).

If a format is not listed, please contact your local

Tektronix representative.

External Instrumentation

Interfaces

System Trigger Output – Asserted whenever

a system trigger occurs (TTL-compatible output,

back-terminated into 50 Ω). BNC type connector.

System Trigger Input – Forces a system trigger

(triggers all modules) when asserted (TTL-compatible,

edge-sensitive, falling-edge latched). BNC type

connector.

External Signal Output – Can be used to drive

external circuitry from a module’s trigger mechanism

(TTL-compatible output, back-terminated into 50 Ω).

BNC type connector.

External Signal Input – Can be used to provide an

external signal to arm or trigger any or all modules

(TTL-compatible, level-sensitive). BNC type connector.

Power

Voltage range/frequency – 90 to 240 VAC at 47

to 63 Hz.

Input current – 5 A maximum at 90 VAC.

Power consumption – 300 W maximum.

Physical Characteristics

TLA5000

Dimensions

in.

Height

285

11.2

Width

438

17.5

Depth

288

11.35

Weight

lb.

Net (without probes)

Shipping (typical)

18.5

Environmental

Temperature –

Operating: +5 ºC to +50 ºC.

Nonoperating: –20 ºC to +60 ºC.

Humidity – 20% to 80%.

Operating: 20% to 80% relative humidity (29 ºC

maximum wet bulb temperature).

Nonoperating: 8% to 80% (29 ºC maximum wet

bulb temperature).

Altitude – Operating: –1,000 ft. to 10,000 ft. (–305

meters to 3,050 meters).

Safety – UL3111-1, CSA1010.1, EN61010-1,

IEC61010-1.

TLA5000 Fiches technique(PDF) 3 Page - List of Unclassifed Manufacturers

TLA5000 Fiches technique(HTML) 3 Page - List of Unclassifed Manufacturers

Html Pages

1 2 3 4

Fiches technique Télécharger

Lien URL