STM32F401 datasheet(61/135 Pages) STMICROELECTRONICS

61 / 135 page

DocID025644 Rev 3

61/135

STM32F401xD STM32F401xE

Electrical characteristics

114

Ambient temperature for 6

suffix version

Maximum power dissipation

–40

°C

Low power dissipation(8)

–40

105

Ambient temperature for 7

suffix version

Maximum power dissipation

–40

105

Low power dissipation(8)

–40

125

Junction temperature range

6 suffix version

–40

105

7 suffix version

–40

125

1. VDD/VDDA minimum value of 1.7 V with the use of an external power supply supervisor (refer to Section 3.14.2: Internal

reset OFF).

2. When the ADC is used, refer to Table 66: ADC characteristics.

3. If VREF+ pin is present, it must respect the following condition: VDDA-VREF+ < 1.2 V.

4. It is recommended to power VDD and VDDA from the same source. A maximum difference of 300 mV between VDD and VDDA

can be tolerated during power-up and power-down operation.

5. Guaranteed by test in production

6. To sustain a voltage higher than VDD+0.3, the internal Pull-up and Pull-Down resistors must be disabled

7. If TA is lower, higher PD values are allowed as long as TJ does not exceed TJmax.

8. In low power dissipation state, TA can be extended to this range as long as TJ does not exceed TJmax.

Table 14. General operating conditions (continued)

Symbol

Parameter

Conditions

Min

Typ

Max

Unit

Table 15. Features depending on the operating power supply range

Operating

power

supply

range

ADC

operation

Maximum

Flash

memory

access

frequency

with no wait

states

(fFlashmax)

Maximum Flash

memory access

frequency with

wait states (1)(2)

I/O operation

Clock output

frequency on

I/O pins(3)

Possible

Flash

memory

operations

VDD =1.7 to

2.1 V(4)

Conversion

time up to

1.2 Msps

20 MHz(5)

84 MHz with 4

wait states

– No I/O

compensation

up to 30 MHz

8-bit erase

and program

operations

only

VDD = 2.1 to

2.4 V

Conversion

time up to

1.2 Msps

22 MHz

84 MHz with 3

wait states

– No I/O

compensation

up to 30 MHz

16-bit erase

and program

operations

VDD = 2.4 to

2.7 V

Conversion

time up to

2.4 Msps

24 MHz

84 MHz with 3

wait states

– I/O

compensation

works

up to 48 MHz

16-bit erase

and program

operations

VDD = 2.7 to

3.6 V(6)

Conversion

time up to

2.4 Msps

30 MHz

84 MHz with 2

wait states

– I/O

compensation

works

–up to

84 MHz

when VDD =

3.0 to 3.6 V

–up to

48 MHz

when VDD =

2.7 to 3.0 V

32-bit erase

and program

operations

STM32F401 Fiches technique(PDF) 61 Page - STMicroelectronics

STM32F401 Fiches technique(HTML) 61 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Fiches technique Télécharger

Lien URL