ICS1892 datasheet(11/148 Pages) ICST

11 / 148 page

Chapter 2

Conventions and Nomenclature

ICS1892, Rev. D, 2/26/01

February 26, 2001

ICS1892

Chapter 2

Conventions and Nomenclature

Table 2-1 lists and explains the conventions and nomenclature used throughout this data sheet.

Table 2-1.

Conventions and Nomenclature

Item

Convention / Nomenclature

Asterisk (*)

Within this table, see the item ‘Pin (or signal) names’

Bits

• A bit in a register is identified using the format ‘register.bit’. For example, bit

0.15 is bit 15 of register 0.

• When a colon is used with bits, it indicates the range of bits. For example,

bits 1.15:11 are bits 15, 14, 13, 12, and 11 of register 1.

• For a range of bits, the order is always from the most-significant bit to the

least-significant bit.

Code groups

Within this table, see the item ‘Symbols’

Colon (:)

Within this table, see these items:

• ‘Bits’

• ‘Pin (or signal) names’

Numbers

• As a default, all numbers use the decimal system (that is, base 10) unless

followed by a lowercase letter. A string of numbers followed by a lowercase

letter:

– A ‘b’ represents a binary (base 2) number

– An ‘h’ represents a hexadecimal (base 16) number

– An ‘o’ represents an octal (base 8) number

• All numerical references to registers use decimal notation (and not

hexadecimal).

Pin (or signal) names

• All pin or signal names are provided in capital letters.

• A pin name that includes a forward slash ‘/’ is a multi-function, configuration

pin. These pins provide the ability to select between two ICS1892

functions. The name provided:

– Before the ‘/’ indicates the pin name and function when the signal level

on the pin is logic zero.

– After the ‘/’ indicates the pin name and function when the signal level on

the pin is logic one.

For example, the HW/SW pin selects between Hardware (HW) mode and

Software (SW) mode.

– When the signal level on the HW/SW pin is logic zero, the ICS1892

Hardware mode is selected.

– When the signal level on the HW/SW pin is logic one, the ICS1892

Software mode is selected.

• An asterisk appended to the end of a pin name or signal name (such as

RESET*) indicates an active-low operation.

• When a colon is used with pin or signal names, it indicates a range. For

example, TXD[3:0] represents pins/signals TXD3, TXD2, TXD1, and TXD0.

• When pin name abbreviations are spelled out, words in parentheses

indicate additional description that is not part of the pin name abbreviation.

ICS1892 Fiches technique(PDF) 11 Page - Integrated Circuit Systems

ICS1892 Fiches technique(HTML) 11 Page - Integrated Circuit Systems

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Fiches technique Télécharger

Lien URL