GLS53 datasheet(34/109 Pages) EMERSON-NETWORKPOWER

34 / 109 page

GLS170 Series, GLS170-M Series Installation & Operating Instructions

Visit our Web site at www.solahd.com or contact Technical Support at (800) 377- 4384 with any questions

P/N: A272-191 Rev 0 3/13/09 Ref: 03366202050/LPS173/OP/03366202230/03366202241

To comply with the published safety standards, the following must be observed when using

this power supply:

1. Maximum ambient temperature for the power supply must not exceed 50°C. Derate

each output 2.5% per degree from 50°C to 70°C ambient temperature for GLS174 and

GLS175.

2. When installing the power supply in the end-use equipment, special attention is

required to ensure safety compliance with the following safety standards: UL60950-1,

EN60950-1, IEC60950-1, and CSA22.2 No. 60950-1-03 for GLS172, GLS173,

GLS174, and GLS175; UL60601-1, EN60601-1, IEC60601-1, and CSA22.2 No.

60601-1-M90 for GLS172-M, GLS173-M, GLS174-M, and GLS175-M. The safety

requirements include creepage distances, clearances, and distance through insulation

between primary wiring and earth or secondary (SELV) wiring.

3. The ac-dc input connector is approved as a component of the power supply, however, it

was not specifically evaluated to IEC60320.

4. This power supply is approved and certified for the rated voltage range of 100 V ac to

250 V ac and/or 120 V dc (minimum) to 300 V dc (maximum).

5. The maximum output power of the supply must not exceed the rating indicated in the

specification sheet.

6. The disconnection from the line must be in the end system.

7. Hazardous voltages exist in the primary circuits. Disconnect power supply before

servicing.

8. When operating with a dc input voltage range, the unit input must be protected by a dc

rated fuse in the end-use installation system.

9. The internal fuse (F1) should only be replaced by a 4A, 250 V ac, type GDA-V/S501

manufactured by Bussmann, type 226004 manufactured by Littelfuse, or type 19194

manufactured by Wickmann.

10. The power supply has no patient applied part.

11. This equipment is considered Class I according to protection against electric shock.

12. This power supply is

marked following the provisions of the Low Voltage Directive,

2006/95/EC.

13. For technical assistance, contact SolaHD Technical Support at (800) 377- 4384 or send

an e-mail to tech@solahd.com. Please visit our Web site at www.solahd.com for addi-

tional product information and specification sheets.

Output Ratings

Model

Output Voltage

(V)

Convection Cooling

30 CFM Forced Air Cooling

Max. Output

Current (A)

Max. Output

Power (W)

Max. Output

Current (A)

Max. Output

Power (W)

GLS172 (-M)

+2.5 to +6

22.0 without cover

15.0 with cover

110 without

cover

75 with cover

35.0

175 with and

without cover

+5 VSTBY

1.0

2.0

+12 (FAN_OUT)

0.5

1.0

GLS173 (-M)

+6 to +12

9.1 without cover

6.25 with cover

15.0

180 with and

without cover

+5 VSTBY

1.0

2.0

+12 (FAN_OUT)

0.5

1.0

GLS174 (-M)

+12 to +24

7.3 without cover

5.33 with cover

12.0

+5 VSTBY

1.0

2.0

+12 (FAN_OUT)

0.5

1.0

GLS175 (-M)

+24 to +54

4.58 without cover

3.125 with cover

7.5

+5 VSTBY

1.0

2.0

+12 (FAN_OUT)

0.5

1.0

Connector PIN Designation

Input Connector

Designation

SK4

Earth GND

Line

Neutral

Output Connector

Designation

SK1

+12 V (FAN_OUT)

+5 VSTBY

Common

V1 SWP (Single wire parallel)

Common

+V1 sense

Sense common

Remote inhibit

DC OK

P OK

SK3

TB-1

Common

TB-2

GLS53 Fiches technique(PDF) 34 Page - Emerson Network Power

GLS53 Fiches technique(HTML) 34 Page - Emerson Network Power

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Fiches technique Télécharger

Lien URL