MTR40 datasheet(13/26 Pages) INTERPOINT

13 / 26 page

Notes

1. Guaranteed by design and/or analysis. Not an in-line test.

2. MTR2805D (standard and /ES) is specified at 25°C only.

3. Up to 90% of the total output current/power is available from either output

providing the positive output is carrying at least 10% of the total output power.

4. Operation is limited below 16 V. See “Figure 27” on page 17.

5. Effect on negative VOUT from 50%/50% loads to 80%/20% or 20%/80% loads.

6. Effect on negative VOUT from 50%/50% loads to 90%/10% or 10%/90% loads.

See “Figure 25” on page 17.

7. Tested with 6800 pF ceramic bypass capacitor connected externally from input

common to case.

8. Indefinite short circuit protection not guaranteed above 125°C case.

8. Recovery time is measured from application of the transient to point at which

VOUT is within 1% of final value.

10. Tested on release from inhibit.

DUAL OUTPUT MODELS - STaNDaRD aND /ES

MTR2805D 2

MTR2812D

MTR2815D

UNITS

PARAMETER

CONDITIONS

MIN

TYP

MAX

MIN

TYP

MAX

MIN

TYP

MAX

OUTPUT VOLTAGE

+ VOUT

4.850

5.00

5.150 11.88 12.00 12.12 14.85 15.00 15.15

VDC

- VOUT

4.825

5.00

5.172 11.58 12.00 12.42 14.47 15.00 15.53

OUTPUT CURRENT 3

EITHER OUTPUT

2.5

4.5 1

1.25

2.25 1

1.00

1.80 1

VIN = 16 TO 40 VDC

TOTAL OUTPUT

—

2.5

—

2.00

OUTPUT POWER 3

EITHER OUTPUT

12.5

22.5 1

27 1

VIN = 16 to 40 VDC

TOTAL OUTPUT

—

OUTPUT RIPPLE

TC = 25°C

—

mV p-p

10 kHz - 2 MHz ± VOUT

TC = -55°C TO +125°C

—

120

—

120

LINE REGULATION 4

+ VOUT

—

VIN = 16 TO 40 VDC

- VOUT

—

100

—

150

—

180

LOAD REGULATION

+ VOUT

—

NO LOAD TO FULL

- VOUT

—

100

—

150

—

180

CROSS REGULATION 1

SEE NOTE 5

—

EFFECT ON -VOUT, 25°C

SEE NOTE 6

—

8.3

—

INPUT VOLTAGE

CONTINUOUS

VDC

NO LOAD TO FULL

TRANSIENT 50 msec.1

—

INPUT CURRENT

NO LOAD

—

–

—

INHIBITED

—

INPUT RIPPLE CURRENT 7 10 kHz - 10 MHz

—

mA p-p

EFFICIENCY

TC = 25°C

—

BALANCED LOAD

TC = -55°C TO +125°C

—

LOAD FAULT 8

POWER DISSIPATION

—

SHORT CIRCUIT

RECOVERY 1

—

1.4

5.0

—

1.4

5.0

—

1.4

5.0

STEP LOAD RESPONSE

TRANSIENT

—

±200

±300

—

±150

±300

—

±200

±400

mV pk

50% - 100% - 50% ± VOUT RECOVERY 1, 9

—

100

200

—

100

200

—

100

200

µs

STEP LINE RESPONSE 1

TRANSIENT 9

—

±200

±400

—

±200

±400

—

±400

±500

mV pk

16 - 40 -16 VDC ± VOUT

RECOVERY 9

—

300

—

300

—

300

µs

START-UP 10

DELAY

—

1.4

—

1.4

—

1.4

FULL LOAD

OVERSHOOT 1

—

180

—

120

—

150

mV pk

CAPACITIVE LOAD 1

TC = 25°C

NO EFFECT ON DC

PERFORMANCE

—

500

—

500

—

500

µF

table 9: eleCtriCal CharaCteristiCs: -55°C to +125°C tC, 28 vDC vin, 100% loaD, Free run, unless otherWise speCiFieD.

Crane Aerospace & Electronics Power Solutions

mTR (40) Single, Dual and Triple DC-DC Converters

28 (16-40) VOlT INPuT – 30 WaTT

www.craneae.com/interpoint

Page 13 of 26

MTR-01 Rev AA - 2013.09.04

MTR40 Fiches technique(PDF) 13 Page - Interpoint Corporation Company

MTR40 Fiches technique(HTML) 13 Page - Interpoint Corporation Company

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

Fiches technique Télécharger

Lien URL