RCM3365 datasheet(21/165 Pages) ETC2

21 / 165 page

User’s Manual

2.3.1 Running Dynamic C via Serial Programming Cable

Dynamic C uses the serial port on your PC that you specified during installation.

If you are using a USB port to connect your computer to the RCM3365/RCM3375 module,

choose Options > Project Options and select “Use USB to Serial Converter” on the

Communications

tab.

2.3.1.1 Run a Sample Program

Use the File menu to open the sample program PONG.C, which is in the Dynamic C

SAMPLES

folder. Press function key F9 to compile and run the program. The STDIO

window will open on your PC and will display a small square bouncing around in a box.

This program shows that the CPU is working. The sample program described in

Section 6.5, “Run the PINGME.C Sample Program,” tests the TCP/IP portion of the board.

2.3.1.2 Troubleshooting

If Dynamic C cannot find the target system (error message "No Rabbit Processor

Detected."

•

Check that the RCM3365/RCM3375 is powered correctly — the red CORE LED on the

Prototyping Board should be lit when the RCM3365/RCM3375 is mounted on the Prototyping

Board and the AC adapter is plugged in

•

Check both ends of the programming cable to ensure that they are firmly plugged into

the PC and the PROG connector, not the DIAG connector, is plugged in to the program-

ming port on the RCM3365/RCM3375 with the marked (colored) edge of the program-

ming cable towards pin 1 of the programming header.

•

Ensure that the RCM3365/RCM3375 module is firmly and correctly installed in its

connectors on the Prototyping Board.

•

Dynamic C uses the COM port specified during installation. Select a different COM

port within Dynamic C. From the Options menu, select Project Options, then select

Communications

. Select another COM port from the list, then click OK. Press

<Ctrl-Y>

to force Dynamic C to recompile the BIOS. If Dynamic C still reports it is

unable to locate the target system, repeat the above steps until you locate the COM port

used by the programming cable.

If Dynamic C appears to compile the BIOS successfully, but you then receive a communi-

cation error message when you compile and load the sample program, it is possible that

your PC cannot handle the higher program-loading baud rate. Try changing the maximum

download rate to a slower baud rate as follows.

•

Locate the Serial Options dialog in the Dynamic C Options > Project Options >

Communications menu. Select a slower Max download baud rate.

If a program compiles and loads, but then loses target communication before you can

begin debugging, it is possible that your PC cannot handle the default debugging baud

rate. Try lowering the debugging baud rate as follows.

•

Locate the Serial Options dialog in the Dynamic C Options > Project Options >

Communications menu. Choose a lower debug baud rate.

RCM3365 Fiches technique(PDF) 21 Page - List of Unclassifed Manufacturers

RCM3365 Fiches technique(HTML) 21 Page - List of Unclassifed Manufacturers

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Fiches technique Télécharger

Lien URL