MPC5602D datasheet(22/77 Pages) FREESCALE

22 / 77 page

MPC5602D Microcontroller Data Sheet, Rev. 3.1

Preliminary—Subject to Change Without Notice

Electrical characteristics

Freescale Semiconductor

NOTE

Stresses exceeding the recommended absolute maximum ratings may cause permanent

damage to the device. This is a stress rating only and functional operation of the device at

these or any other conditions above those indicated in the operational sections of this

specification are not implied. Exposure to absolute maximum rating conditions for

extended periods may affect device reliability. During overload conditions (VIN >VDD or

VIN <VSS), the voltage on pins with respect to ground (VSS) must not exceed the

recommended values.

4.5

Recommended operating conditions

Table 8. Recommended operating conditions (3.3 V)

Symbol

Parameter

Conditions

Value

Unit

Min

Max

VSS

SR — Digital ground on VSS_HV pins

—

VDD

1 100 nF capacitance needs to be provided between each V

DD/VSS pair.

SR — Voltage on VDD_HV pins with respect to ground

(VSS)

—3.0

3.6

VSS_LV

2 330 nF capacitance needs to be provided between each V

DD_LV/VSS_LV supply pair.

SR — Voltage on VSS_LV (low voltage digital supply)

pins with respect to ground (VSS)

—VSS  0.1 VSS +0.1

VDD_BV

3 470 nF capacitance needs to be provided between V

DD_BV and the nearest VSS_LV (higher value may be needed

depending on external regulator characteristics).

SR — Voltage on VDD_BV pin (regulator supply) with

respect to ground (VSS)

—3.0

3.6

Relative to VDD VDD  0.1 VDD +0.1

VSS_ADC SR — Voltage on VSS_HV_ADC (ADC reference) pin

with respect to ground (VSS)

—VSS  0.1 VSS +0.1

VDD_ADC

4 100 nF capacitance needs to be provided between V

DD_ADC/VSS_ADC pair.

SR — Voltage on VDD_HV_ADC pin (ADC reference)

with respect to ground (VSS)

—3.05

5 Full electrical specification cannot be guaranteed when voltage drops below 3.0 V. In particular, ADC electrical

characteristics and I/Os DC electrical specification may not be guaranteed. When voltage drops below VLVDHVL,

device is reset.

3.6

Relative to VDD VDD  0.1 VDD +0.1

VIN

SR — Voltage on any GPIO pin with respect to ground

(VSS)

—VSS  0.1

—

Relative to VDD

—VDD +0.1

IINJPAD

SR — Injected input current on any pin during overload

condition

—

55

IINJSUM

SR — Absolute sum of all injected input currents during

overload condition

—

50

TVDD

SR — VDD slope to ensure correct power up

6 Guaranteed by device validation

—

TBD

0.25

V/µs

SR — Ambient temperature under bias

fCPU  48 MHz

40

125

°C

SR — Junction temperature under bias

—

40

150

MPC5602D Fiches technique(PDF) 22 Page - Freescale Semiconductor, Inc

MPC5602D Fiches technique(HTML) 22 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77

Fiches technique Télécharger

Lien URL