5000 datasheet(63/104 Pages) INTEL

63 / 104 page

Dual-Core Intel® Xeon® Processor 5000 Series Datasheet

Signal Definitions

D[63:0]#

I/O

D[63:0]# (Data) are the data signals. These signals provide a 64-bit data path

between the processor FSB agents, and must connect the appropriate pins on all

such agents. The data driver asserts DRDY# to indicate a valid data transfer.

D[63:0]# are quad-pumped signals, and will thus be driven four times in a

common clock period. D[63:0]# are latched off the falling edge of both

DSTBP[3:0]# and DSTBN[3:0]#. Each group of 16 data signals

correspond to a pair of one DSTBP# and one DSTBN#. The following table

shows the grouping of data signals to strobes and DBI#.

Furthermore, the DBI# signals determine the polarity of the data signals.

Each group of 16 data signals corresponds to one DBI# signal. When the

DBI# signal is active, the corresponding data group is inverted and

therefore sampled active high.

DBI[3:0]#

I/O

DBI[3:0]# (Data Bus Inversion) are source synchronous and indicate the polarity of

the D[63:0]# signals. The DBI[3:0]# signals are activated when the data on the data

bus is inverted. If more than half the data bits, within, within a 16-bit group, would

have been asserted electronically low, the bus agent may invert the data bus signals

for that particular sub-phase for that 16-bit group.

DBR#

DBR# is used only in systems where no debug port connector is implemented on the

system board. DBR# is used by a debug port interposer so that an in-target probe

can drive system reset. If a debug port connector is implemented in the system,

DBR# is treated as a no connect for the processor socket. DBR# is not a processor

signal.

DBSY#

I/O

DBSY# (Data Bus Busy) is asserted by the agent responsible for driving data on the

processor FSB to indicate that the data bus is in use. The data bus is released after

DBSY# is deasserted. This signal must connect the appropriate pins on all processor

FSB agents.

DEFER#

DEFER# is asserted by an agent to indicate that a transaction cannot be guaranteed

in-order completion. Assertion of DEFER# is normally the responsibility of the

addressed memory or I/O agent. This signal must connect the appropriate pins of all

processor FSB agents.

DP[3:0]#

I/O

DP[3:0]# (Data Parity) provide parity protection for the D[63:0]# signals. They are

driven by the agent responsible for driving D[63:0]#, and must connect the

appropriate pins of all processor FSB agents.

DRDY#

I/O

DRDY# (Data Ready) is asserted by the data driver on each data transfer, indicating

valid data on the data bus. In a multi-common clock data transfer, DRDY# may be

deasserted to insert idle clocks. This signal must connect the appropriate pins of all

processor FSB agents.

Table 5-1.

Signal Definitions (Sheet 3 of 8)

Name

Type

Description

Notes

Data Group

DSTBN#/

DSTBP#

DBI#

D[15:0]#

D[31:16]#

D[47:32]#

D[63:48]#

DBI[3:0]# Assignment to Data Bus

Bus Signal

Data Bus Signals

DBI0#

D[15:0]#

DBI1#

D[31:16]#

DBI2#

D[47:32]#

DBI3#

D[63:48]#

5000 Fiches technique(PDF) 63 Page - Intel Corporation

5000 Fiches technique(HTML) 63 Page - Intel Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Fiches technique Télécharger

Lien URL