TC7652CPD datasheet(2/6 Pages) TELCOM

2 / 6 page

3-282

TELCOM SEMICONDUCTOR, INC.

TC7652

LOW NOISE, CHOPPER-STABILIZED

OPERATIONAL AMPLIFIER

ABSOLUTE MAXIMUM RATINGS*

Total Supply Voltage (VDD to VSS) ........................... +18V

Input Voltage ........................ (VDD + 0.3V) to (VSS – 0.3V)

Voltage on Oscillator Control Pins ................... VDD to VSS

Duration of Output Short Circuit ......................... Indefinite

Current Into Any Pin ................................................. 10mA

While Operating (Note 1) ..................................100

µA

Package Power Dissipation (TA ≤ 70°C)

8-Pin Plastic DIP ............................................. 730mW

14-Pin Plastic DIP ........................................... 800mW

Storage Temperature Range ................ – 65

°C to +150°C

Operating Temperature Range

C Device ................................................ 0

°C to +70°C

I Device ............................................. – 25

°C to +85°C

Lead Temperature (Soldering, 10 sec) ................. +300

°C

ELECTRICAL CHARACTERISTICS: VDD = +5V, VSS = – 5V, TA = +25°C, unless otherwise indicated.

Symbol

Parameter

Test Conditions

Min

Typ

Max

Unit

VOS

Input Offset Voltage

TA = +25°C—

±2

±5

µV

°C < TA < +70°C—

±10

—

TCVOS

Average Temperature Coefficient of

°C < TA < +70°C

—

0.01

0.05

µV/°C

Input Offset Voltage

VOS/DT

Offset Voltage vs Time

—

150

—

nV/mo

IBIAS

Input Bias Current

TA = +25°C

—

100

(CLK On)

°C < TA < +70°C

—

100

—

– 25

°C < TA < +85°C

—

250

1000

IBIAS

Input Bias Current

TA = +25°C

—

(CLK Off)

°C < TA < +70°C—

—

– 25

°C < TA < +85°C

—

100

—

IOS

Input Offset Current

—

150

RIN

Input Resistance

—

1012

—W

Large Signal Voltage Gain

RL = 10kW, VOUT = ±4V

120

150

—

VOUT

Output Voltage Swing

RL = 10kW

±4.7

±4.85

—

(Note 2)

RL = 100kW

—

±4.95

—

CMVR

Common-Mode

– 4.3

—

+3.5

Voltage Range

MRR

Common-Mode

CMVR = – 4.3V to +3.5V

120

140

—

Rejection Ratio

PSRR

Power Supply

±3V to ±8V

120

140

—

Rejection Ratio

Input Noise Voltage

RS = 100W, DC to 1Hz

—

0.2

1.5

µVP-P

DC to 10Hz

—

0.7

µVP-P

Input Noise Current

f = 10Hz

—

0.01

—

pA/

√Hz

GBW

Unity-Gain Bandwidth

—

0.4

—

MHz

Slew Rate

CL = 50 pF, RL = 10kW

—

µsec

Overshoot

—

VDD, VSS

Operating Supply Range

—

Supply Current

No Load

—

fCH

Internal Chopping Frequency

Pins 12 – 14 Open (DIP)

100

275

—

Clamp ON Current (Note 3)

RL = 100kW

100

—

µA

Clamp OFF Current (Note 3)

– 4V

≤ VOUT < +10V

—

NOTES: 1. Limiting input current to 100

µA is recommended to avoid latch-up problems. Typically, 1mA is safe; however, this is not guaranteed.

2. Output clamp not connected. See typical characteristics curves for output swing versus clamp current characteristics.

*Static-sensitive device. Unused devices must be stored in conductive material. Protect devices from static discharge and static fields. Stresses above

those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only and functional operation of

the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to Absolute

Maximum Rating Conditions for extended periods may affect device reliability.

TC7652CPD Fiches technique(PDF) 2 Page - TelCom Semiconductor, Inc

TC7652CPD Fiches technique(HTML) 2 Page - TelCom Semiconductor, Inc

Html Pages

1 2 3 4 5 6

Fiches technique Télécharger

Lien URL