LP5904

SNVS637G – MARCH 2011 – REVISED APRIL 2013

www.ti.com

ELECTRICAL CHARACTERISTICS

(1) (2)

Limits in standard typeface are for TA = 25°C. Limits in boldface type apply over the full operating junction temperature range

(–40°C

≤ TJ ≤ +125°C). Unless otherwise noted, specifications apply to the LP5904 Typical Application Circuit with: VIN = VOUT

(NOM) + 1.0V, VEN = 1.2V, CIN = 1.0 µF, COUT = 1.0 µF, IOUT = 1.0 mA.

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNIT

VIN

Input Voltage

2.2

5.5

V

VIN = (VOUT(NOM) + 1.0V) to 5.5V,

Output Voltage Tolerance

–2

2

%

IOUT = 1mA to 200 mA

VIN = (VOUT(NOM) + 1.0V) to 5.0V,

0.06

IOUT = 1 mA

ΔVOUT

Line Regulation

%/V

VIN = (VOUT(NOM) + 1.0V) to 5.5V,

0.16

IOUT = 1 mA

Load Regulation

IOUT = 1mA to 200 mA

0.002

%/mA

Load Current

See (3)

0

200

ILOAD

mA

Maximum Output Current

200

VEN = 1.2V, IOUT = 0 mA

11

20

IQ

Quiescent Current(4)

VEN = 1.2V, IOUT = 200 mA

250

325

µA

VEN = 0.3V (Disabled)

0.2

1.0

IG

Ground Current(5)

IOUT = 0 mA (VEN = 1.2V)

12.2

µA

IOUT = 100 mA

45

VDO

Dropout Voltage(6)

mV

IOUT = 200 mA

95

150

ISC

Short Circuit Current Limit

See (7)

220

450

mA

f = 100 Hz, IOUT = 10 mA

88

f = 1 kHz, IOUT = 10 mA

80

Power Supply Rejection

PSRR

f = 10 kHz, IOUT = 10 mA

70

dB

Ratio(8)

f = 100 kHz, IOUT = 10 mA

50

f = 2MHz, IOUT = 10 mA

30

IOUT = 1mA

10

BW = 10 Hz to 100

eN

Output Noise Voltage(8)

µVRMS

kHz

IOUT = 200 mA

6.5

Temperature

160

TSHUTDOWN

Thermal Shutdown

°C

Hysteresis

15

LOGIN INPUT THRESHOLDS

VIL

Low Input Threshold (VEN)

VIN = 2.2V to 5.5V

0.4

V

VIH

High Input Threshold (VEN)

VIN = 2.2V to 5.5V

1.2

V

VEN = 5.5V and VIN = 5.5V

5.5

IEN

Input Current at VEN Pin

(9)

µA

VEN = 0.0V and VIN = 5.5V

0.001

(1)

All voltages are with respect to the potential at the GND pin.

(2)

Min and Max limits are specified by design, test, or statistical analysis. Typical numbers are not specified, but do represent the most

likely norm.

(3)

The device maintains a stable, regulated output voltage without a load current.

(4)

Quiescent current is defined here as the difference in current between the input voltage source and the load at VOUT.

(5)

Ground current is defined here as the total current flowing to ground as a result of all input voltages applied to the device.

(6)

Dropout voltage is the voltage difference between the input and the output at which the output voltage drops to 100 mV below its

nominal value. This specification does not apply for input voltages below 2.2V.

(7)

Short Circuit Current is measured with VOUT pulled to 0V and VIN worst case = 5.5V.

(8)

This specification is ensured by design.

(9)

There is a 1M

Ω resistor between VEN and ground on the device.

4

Submit Documentation Feedback

Copyright © 2011–2013, Texas Instruments Incorporated

Product Folder Links: LP5904