X24C01APG datasheet(8/13 Pages) ICMIC

8 / 13 page

X24C01A

ABSOLUTE MAXIMUM RATINGS*

Temperature Under Bias

.................. –65°C to +135°C

Storage Temperature ....................... –65°C to +150°C

Voltage on any Pin with

Respect to V SS ............................... –1.0V to +7V

D.C. Output Current ............................................ 5 mA

Lead Temperature (Soldering,

10 Seconds)

............................. 300°C

*COMMENT

Stresses above those listed under “Absolute Maximum

Ratings” may cause permanent damage to the device.

This is a stress rating only and the functional operation of the

device at these or any other conditions above those

indicated in the operational sections of this specification is not

implied. Exposure to absolute maximum rating conditions for

extended periods may affect device reliability.

RECOMMENDED OPERATING CONDITIONS

Temperature

Min.

Max.

Commercial

0°C

70°C

Industrial

–40°C

+85°C

Military

–55°C

+125°C

3841 PGM T02

Supply Voltage

Limits

X24C01A

4.5V to 5.5V

X24C01A-3.5

3.5V to 5.5V

X24C01A-3

3V ± 5.5V

X24C01A-2.7

2.7V to 5.5V

3841 PGM T03

D.C. OPERATING CHARACTERISTICS (Over recommended operating conditions unless otherwise specified)

Limits

Symbol

Parameter

Min.

Max.

Units

Test Conditions

lCC1

Power Supply Current

SCL = VCC x 0.1/VCC x 0.9 Levels

(read)

@ 100 KHz, SDA = Open, All Other

Inputs = GND or VCC – 0.3V

ICC2

Power Supply Current

SCL = VCC x 0.1/VCC x 0.9 Levels

(write)

@ 100 KHz, SDA = Open, All Other

Inputs = GND or VCC – 0.3V

ISB(1)

Standby Current

∝

SCL = SDA = VCC – 0.3V, All Other

Inputs = GND or VCC, VCC = 5.5V

(1)

Standby Current

∝

SCL = SDA = VCC – 0.3V, All Other

Inputs =

GND or VCC, VCC= 3.3V + 10%

ILI

Input Leakage Current

∝

VIN = GND to VCC

ILO

Output Leakage Current

∝

VOUT = GND to VCC

(2)

Input Low Voltage

–1.0

VCC x 0.3

VIH(2)

Input High Voltage

VCC x 0.7

VCC + 0.5

VOL

Output Low Voltage

0.4

IOL = 3 mA

3841 PGM T04

CAPACITANCE TA = 25°C, f = 1.0MHZ, VCC = 5V

Symbol

Test

Max.

Units

Conditions

I/O

(3)

Input/Output Capacitance (SDA)

VI/O = 0V

(3)

Input Capacitance (A0, A1, A2, SCL, WC)

VIN = 0V

3841 PGM T06

Notes:(1) Must perform a stop command prior to measurement. (2)

IL min. and VIH max. are for reference only and are not tested. (3)

This parameter is periodically sampled and not 100% tested.

X24C01APG Fiches technique(PDF) 8 Page - IC MICROSYSTEMS

X24C01APG Fiches technique(HTML) 8 Page - IC MICROSYSTEMS

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13

Fiches technique Télécharger

Lien URL