SC615AEVB datasheet(1/12 Pages) SEMTECH

No de pièce	SC615AEVB

Description	Charge Pump Flash LED Driver

PDF	12 Pages

Scroll/Zoom	100%

Fabricant	SEMTECH [Semtech Corporation]

Site Internet	http://www.semtech.com

Logo

1 / 12 page

www.semtech.com

1

POWER MANAGEMENT

SC615A

Charge Pump

Flash LED Driver

September 22, 2005

Typical Application Circuit

Applications

Features

Two Selectable Modes - Flash and Spotlight

Up to 700mA Output - Flash Mode

Up to 280mA Output - Spotlight Mode

500mA Over Temperature Range and Voltage

Range - Flash Mode

Spotlight mode set to 40% of Flash Current

3.0V to 5.25V Input Range

External Flash Control Pin for Synchronization to a

Camera Module or Graphics Controller

Short Circuit, Over-Voltage, and Over-Temperature

Protection

Soft-Start Functionality

Two Control Inputs for Maximum Versatility

Shutdown Current < 2

µA

Micro Lead Package MLPD-10, 3mm x 3mm

Mobile Camera Phones

Digital Cameras

PDAs with Built-in Cameras

The SC615A is a high-current charge pump designed spe-

cifically for use with white LEDs used in camera flash

applications. Only two small bucket capacitors are re-

quired to develop the output drive, providing a low EMI

solution compared to inductive boost regulators.

The SC615A has two modes of operation: Flash mode

and Spotlight mode. In Flash mode, the SC615A is ca-

pable of delivering 500mA of regulated current for a du-

ration of 500ms or up to 700mA for a reduced duration.

In Spotlight mode the SC615A outputs 40% of the Flash

mode current and can remain enabled continuously.

An external resistor is connected in series with the LED

to set the current. In Flash mode, this resistor can

dissipate up to 175mW, reducing the power dissipation

requirement of the SC615A. The flash input (FLASH)

overrides the control input (CTRL) to make sure the flash

function is activated when called for.

The thermally efficient MLPD-10 package and ceramic

bypass and bucket capacitors make the SC615A a high

output current driver that requires minimal PCB area.

Description

3.0V to 5.25V

SC615A

VIN

1

C2-

2

C2+

10

C1-

4

C1+

8

VOUT

9

FLASH

5

CTRL

7

GND

3

ISET

6

1

µF

1

µF

FLASH

CTRL

1

µF

white LED

0.5

Ω

10

µF

C1

C2

Numéro de pièce similaire - SC615AEVB

Fabricant	No de pièce	Fiches technique	Description
Semtech Corporation	SC615AEVB	225Kb / 12P	Charge Pump Flash LED Driver

More results

Description similaire - SC615AEVB

Fabricant	No de pièce	Fiches technique	Description
Sipex Corporation	SP6685	143Kb / 10P	Charge Pump LED Driver For Camera Flash
Advanced Analogic Techn...	AAT3170	467Kb / 15P	High Current LED Flash Driver Charge Pump IC
Advanced Analog Technol...	AAT3172	455Kb / 15P	High Current LED Flash Driver Charge Pump IC 3172.2006.05.1.5
Semtech Corporation	SC615	202Kb / 12P	Charge Pump Flash LED Driver
	SC605	361Kb / 12P	Charge Pump Flash LED Driver
	SC635	362Kb / 12P	Charge Pump Flash LED Driver
	SC619	205Kb / 13P	Charge Pump Flash LED Driver with Safety Timer
Advanced Analogic Techn...	AAT3170	377Kb / 15P	High Current LED Flash Driver Charge Pump IC
Semtech Corporation	SC615A	225Kb / 12P	Charge Pump Flash LED Driver
Global Mixed-mode Techn...	G5916	42Kb / 1P	Flash LED Driver with 700mA Charge Pump

More results

SC615AEVB Fiches technique(PDF) 1 Page - Semtech Corporation

SC615AEVB Fiches technique(HTML) 1 Page - Semtech Corporation

Numéro de pièce similaire - SC615AEVB

Description similaire - SC615AEVB

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12

Fiches technique Télécharger

Lien URL