SPC58EG80C3 datasheet(131/139 Pages) STMICROELECTRONICS

131 / 139 page

DS11758 Rev 6

131/139

SPC584Gx, SPC58EGx, SPC58NGx

Revision history

138

06-Jul-2017

3 (cont’)

Table 22: External 40 MHz oscillator electrical specifications:

– Classification for parameters “CS_EXTAL” and “CS_EXTAL” changed

from “T” to “D”.

– Updated classification, conditions, min and max values for

parameter “gm”.

– Footnote “Ixatl is the oscillator...Test circuit is shown in Figure 8”

modified to “Ixatl is the oscillator...startup of the oscillator”.

– Minimum value of parameter “VIHEXT” updated from “VREF+0.6” to

“VREF+0.75”

– Maximum value of parameter “VILEXT” updated from “VREF-0.6” to

“VREF-0.75”

– Parameter “gm”, value “D” updated to “P” for “fXTAL < 8 MHz”, and

“D” for others.

– Footnote “This parameter is...100% tested” updated to “Applies to

an...to crystal mode”. Also added to parameter “VILEXT”.

– For parameters “VIHEXT” and “VILEXT”, Condition “–” updated to

“VREF = 0.29 * VDD_HV_IO_JTAG”

– Parameter “gm”, value “D” updated to “P” for “fXTAL < 8 MHz”, and

“D” for others.

– Footnote “This parameter is...100% tested” updated to “Applies to

an...to crystal mode”. Also added to parameter “VILEXT”.

– For parameters “VIHEXT” and “VILEXT”, Condition “–” updated to

“VREF = 0.29 * VDD_HV_IO_JTAG”

– Updated parameters CS_EXTAL and CS_XTAL.

Renamed the section “RC oscillator 1024 kHz” to Section 4.11.4: Low

power RC oscillator“

Table 23: 32 kHz External Slow Oscillator electrical specifications:

– For parameter “gmsxosc”, changed the cassification to “P”.

Table 24: Internal RC oscillator electrical specifications:

– For parameter “IFIRC”, replaced max value of 300 with 600.

– Added footnote to the description.

– For parameter IFIRC, changed the max value to 600 and added

– Min, Typ and Max value of ”

δfvar_SW” updated from “-1”, “-”, “1” to “-

0.5”, “+0.3” and “0.5” respectively.

Table 25: 1024 kHz internal RC oscillator electrical characteristics:

– For parameter “

δfvar_T”, and “δfvar_V“ changed the cassification to

“P”.

– For parameter “

δfvar_V”, minimum and maximum value updated

from “-0.05” and “+0.05” to “-5” and “+5”

Table 26: ADC pin specification:

–For ILKG, changed condition “C” to “—”.

– Added parameter “IINJ1”

– For parameter CP2, updated the max value to “1”.

Table 75. Document revision history (continued)

Date

Revision

Changes

SPC58EG80C3 Fiches technique(PDF) 131 Page - STMicroelectronics

SPC58EG80C3 Fiches technique(HTML) 131 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Fiches technique Télécharger

Lien URL